Commercial Metal Roof Coating
Standing-seam and ribbed panels get primed, re-fastened, and coated around every curb and clamp.
Commercial metal roof coatingCommercial Roofs · East Granby, CT
East Granby Metal Roof Coating Contractor
Sealing Rooftop Unit Curbs And Solar Rack Feet On Metal
As an East Granby metal roof coating contractor, we seal and coat metal roofs crowded with rooftop units, exhaust fans, and solar racks, starting with every curb and mount.
Metal Roof Coating Around Rooftop Equipment in East Granby
East Granby metal roof coating jobs often involve roofs carrying more than panels: HVAC units on curbs, exhaust fans, conduit runs, and sometimes solar racks clamped to the seams. Each mount is a place water gets in, and each one has to be coated around.
We map every penetration first and talk with your HVAC or solar provider before anything is moved, so equipment that must stay running stays running.
- Every curb and fan base sealed with fabric
- Solar clamps and rail feet coated around, never over wiring
- HVAC and solar providers looped in before work
Penetration Leaks We Seal Before Metal Roof Coating in East Granby
On equipment-heavy roofs, these are the leak points we check first.
- Repair First
Split Curb Flashing
The flashing at a unit curb cracks as the unit vibrates. It gets cut out and replaced.
- Watch
Loose Solar Clamp Seals
Clamps on standing seams can let water wick in. We seal around them without touching wiring.
- Call Now
A Leak Below A Unit
Water dripping near a supply diffuser means the curb is open now. Call us.
- Repair First
Conduit Through Panels
Old conduit penetrations sealed with caulk only start leaking after a few winters.
- Watch
Screws Near Fan Bases
Vibration loosens screws around exhaust fans faster than anywhere else.
Benefits of Coating Your Roof
On a busy roof, coating closes the many small openings that equipment creates.
- Office buildings
- Light manufacturing
- Solar-equipped roofs
- Labs and clean spaces
Curbs Stop Leaking
Each curb gets fabric-reinforced flashing tied into the coating around it.
Panels Stay Put
Coating goes around rack feet, so solar arrays stay installed during the work.
Equipment Keeps Running
Units that cool critical rooms stay on; we work around them on a planned order.
Less Heat Under Units
A reflective film cuts roof heat around units that already work hard in summer.
Commercial Roof Coating Options for East Granby
Busy East Granby roofs often need more than one system; each section gets the one that fits.
Silicone Roof Coating
Flat zones between units where condensate pools get silicone, which handles standing water.
Silicone roof coating
Acrylic Roof Coating
Sloped panels away from the equipment take acrylic in two coats.
Acrylic roof coating
Spray Foam Roofing
Areas crowded with pipes and supports can take spray foam, which fills around each one.
Spray foam roofing
Shingle Roof Coating
Shingle-roofed entries and canopies on the same property get a shingle coating.
Shingle roof coatingWater Dripping Near A Ceiling Diffuser?
Leaking Now
Call and tell us which room and which unit sits above it; the curb is the first thing we check.
Call UsPlanning Ahead
Planning a coating around your units and racks? Get a ballpark range by roof size.
Get A Free Ballpark EstimateMetal Roof Coating Sequence for Busy East Granby Roofs
Five steps that put the penetrations first.
Inspect Your Roof
We count and photograph every curb, fan, clamp, and conduit penetration, and note which units cool rooms that have to stay cool during the work.
Coordinate With Providers
Your HVAC and solar contacts get our schedule ahead of time, so nothing gets shut off, unplugged, or moved without them on hand.
Rebuild Curb Flashing
Cracked curb flashing is cut out, and new flashing with reinforcing fabric goes in at each unit and fan base before the field is touched.
Prime And Seal Panels
Rusted areas between units get primer, and side laps, screw heads, and old conduit holes get sealant so the field is tight.
Coat Around Equipment
Field coats go on around curbs and rack feet at full thickness, keeping coating off wiring, unit cabinets, and solar connectors.
East Granby Neighbors We Also Work In
Offices, shops, and plants in these towns are where we coat most. Elsewhere? Call us or send us a message.
Thompsonville
Storefront blocks; shared-wall flashing and alley staging.
Thompsonville metal roof coatingSuffield
Farm and storage roofs; washers and laps.
Suffield metal roof coatingStafford Springs
Older patched roofs; adhesion tests first.
Stafford Springs metal roof coatingWindsor Locks
Warehouses and docks; staging out of truck lanes.
Windsor Locks metal roof coatingHazardville
Strip plazas; one storefront at a time.
Hazardville metal roof coatingGranby
Weather windows; repairs early, coating in dry stretches.
Granby metal roof coatingSomers
Churches and schools; dates set around events.
Somers metal roof coatingEllington
Light industrial; storm repairs before coating.
Ellington metal roof coatingBroad Brook
Several buildings; phased plan, worst roof first.
Broad Brook metal roof coatingEast Windsor
Large warehouses; coated in sections.
East Windsor metal roof coatingUnion
Rural metal buildings; fully supplied trip.
Union metal roof coatingStafford
Roofs with repair history; written record.
Stafford metal roof coatingWillington
Eaves, gutters, and edge trim first.
Willington metal roof coatingChaplin
Coat-now versus replace-first areas.
Chaplin metal roof coatingEast Granby Metal Roof Coating Questions
Answers for owners of roofs with units and solar.
Equipment
Can you coat a metal roof that has solar panels?
Yes, around the racks. We coat up to and around each clamp and rail foot and keep coating off wiring. Removing the array is only needed when panels under it are rusted through.
Do rooftop units have to be shut down?
Most stay on. A unit is switched off only for the short time its curb flashing is replaced, and we set that time with your HVAC provider.
Do exhaust fans need new curbs?
Only when the curb itself is rotted or rusted through. Most fan curbs keep their frame and get new flashing, fabric, and coating, while units with failed curbs get a curb replacement priced as its own line.
Cost
What does East Granby metal roof coating cost with lots of equipment?
As a ballpark, about $2.50 to $4 per square foot of roof area. Many curbs and mounts push a roof toward the top of the range, because each one takes hand work.
Do you do metal roof coating for East Granby businesses with solar?
Yes. We coordinate with the solar owner or installer, coat around the rack, and seal clamp points on standing seams.
Does more equipment mean a longer job?
Somewhat. Each curb and clamp takes hand work before the field coat, so a roof with many units takes longer than an open roof of the same size. You see the schedule after the inspection.
Local
Is there a metal roof coating contractor near East Granby?
Yes. We cover East Granby from Enfield. Call us or request a ballpark estimate, and we set up a roof walk.
Who issues roof permits in East Granby?
The East Granby building department handles permits for commercial roof work in town; check with them before work starts.
Can you coordinate with our solar installer's warranty?
We share our plan with the solar owner or installer before work starts and coat only around their hardware. Questions about their warranty terms go to them, and we follow any rules they set for working near the array.
Hire a East Granby Metal Roof Coating Contractor
Send a list of the units and racks on your roof, and we will plan the inspection of your East Granby roof.